| MOQ: | 1 |
| Price: | Negotiable |
| Standard Packaging: | Cartons |
| Delivery Period: | 20 work days |
| Supply Capacity: | 10000pcs/month |
OWP-BL1500H-D3-1 — 150 L/min Stainless-Steel Coolant Pump for EV Battery Swap Station Cooling
Product Overview
Battery swap stations repeatedly charge fresh packs at high current, demanding rapid, contamination-free coolant circulation. The OWP-BL1500H-D3-1 delivers 150 L/min at 30 m head on a DC48V supply, in a leak-free canned centrifugal configuration. All wetted metals are 304 stainless steel, ports use φ64 mm sanitary clamps over a φ30 mm bore, and the unit tolerates -40°C to 65°C media for outdoor station installations.
Specifications
| Group | Item | Value |
|---|---|---|
| Supply | Voltage range / rating | DC36–58V / DC48V |
| Consumption | 1500W | |
| Performance | Flow at rated head | 150 L/min (30 m) |
| Pressure limits | -0.75~10 Bar | |
| Noise | At 1 m | ≤65 dB |
| Media | Allowed fluids / temperature | Deionized water, antifreeze / -40°C~65°C |
| Site conditions | Humidity / altitude | 5–95% / ≤3000 m |
| Wetted side | Metal material | 304 stainless steel |
| Pipework | Bore / connection | φ30 mm / φ64 mm tri-clamp |
| Longevity | Rated service life | ≥20,000 h |
| Interface | Protocol / sealing | RS485 / IP67 |
Application
A swap station's cooling skid must pull heat from freshly swapped packs during fast charging and hold setpoint until the next vehicle arrives. The pump's DC36–58V input suits station DC buses fed from batteries or rectifiers, allowing ride-through during grid fluctuations. Sanitary tri-clamps speed up pack-side plumbing changes, and IP67 sealing withstands washdown and outdoor exposure common at station sites.
Main Points & Industry Demands
Swap operations cycle hardware between idle and maximum load many times per day, so the cooling pump faces frequent start-stop transients rather than steady data-center duty. Station operators also run lean maintenance crews, which pushes equipment toward tool-free servicing and long intervals between attention. Coolant loss near charging equipment is a safety concern, making leakage prevention a hard requirement. The combined profile favors seal-less pumps with robust bearings, DC bus compatibility, and quick-disconnect fluid connections.
Product Advantages as Core Solutions
Operational Mechanism
Station coolant enters the impeller eye axially; the BLDC-driven twisted blades accelerate it radially, and the volute raises pressure to overcome the pack cold-plate circuit and charging skid heat exchanger. The rotor turns inside a stainless can in contact with the fluid, which cools the motor section and lubricates the friction pair—no dynamic seal exists to service. RS485 hands speed and health data to the station controller.
Selection Guide
By the 1.5 L/min-per-kW convention, the rated flow corresponds to approximately 100 kW of removable heat—well above what a single swap bay generates, so the pump can cover multiple charging positions or guarantee cooldown of a full pack within tight cycle targets. Since station loops are short, actual head demand is modest; confirm the duty point against real plumbing to avoid unnecessary throttling.
FAQ
Q1: Can connection orientation or mounting be customized for skid integration?
A: Customization is supported, with rapid-response technical support during design-in.
Q2: What supply capacity exists for network-wide station rollouts?
A: Monthly production capacity is 10,000 units, with a 20-working-day lead time.
Q3: What warranty and lifetime should station operators expect?
A: Two-year warranty and a working life exceeding 20,000 hours.
| MOQ: | 1 |
| Price: | Negotiable |
| Standard Packaging: | Cartons |
| Delivery Period: | 20 work days |
| Supply Capacity: | 10000pcs/month |
OWP-BL1500H-D3-1 — 150 L/min Stainless-Steel Coolant Pump for EV Battery Swap Station Cooling
Product Overview
Battery swap stations repeatedly charge fresh packs at high current, demanding rapid, contamination-free coolant circulation. The OWP-BL1500H-D3-1 delivers 150 L/min at 30 m head on a DC48V supply, in a leak-free canned centrifugal configuration. All wetted metals are 304 stainless steel, ports use φ64 mm sanitary clamps over a φ30 mm bore, and the unit tolerates -40°C to 65°C media for outdoor station installations.
Specifications
| Group | Item | Value |
|---|---|---|
| Supply | Voltage range / rating | DC36–58V / DC48V |
| Consumption | 1500W | |
| Performance | Flow at rated head | 150 L/min (30 m) |
| Pressure limits | -0.75~10 Bar | |
| Noise | At 1 m | ≤65 dB |
| Media | Allowed fluids / temperature | Deionized water, antifreeze / -40°C~65°C |
| Site conditions | Humidity / altitude | 5–95% / ≤3000 m |
| Wetted side | Metal material | 304 stainless steel |
| Pipework | Bore / connection | φ30 mm / φ64 mm tri-clamp |
| Longevity | Rated service life | ≥20,000 h |
| Interface | Protocol / sealing | RS485 / IP67 |
Application
A swap station's cooling skid must pull heat from freshly swapped packs during fast charging and hold setpoint until the next vehicle arrives. The pump's DC36–58V input suits station DC buses fed from batteries or rectifiers, allowing ride-through during grid fluctuations. Sanitary tri-clamps speed up pack-side plumbing changes, and IP67 sealing withstands washdown and outdoor exposure common at station sites.
Main Points & Industry Demands
Swap operations cycle hardware between idle and maximum load many times per day, so the cooling pump faces frequent start-stop transients rather than steady data-center duty. Station operators also run lean maintenance crews, which pushes equipment toward tool-free servicing and long intervals between attention. Coolant loss near charging equipment is a safety concern, making leakage prevention a hard requirement. The combined profile favors seal-less pumps with robust bearings, DC bus compatibility, and quick-disconnect fluid connections.
Product Advantages as Core Solutions
Operational Mechanism
Station coolant enters the impeller eye axially; the BLDC-driven twisted blades accelerate it radially, and the volute raises pressure to overcome the pack cold-plate circuit and charging skid heat exchanger. The rotor turns inside a stainless can in contact with the fluid, which cools the motor section and lubricates the friction pair—no dynamic seal exists to service. RS485 hands speed and health data to the station controller.
Selection Guide
By the 1.5 L/min-per-kW convention, the rated flow corresponds to approximately 100 kW of removable heat—well above what a single swap bay generates, so the pump can cover multiple charging positions or guarantee cooldown of a full pack within tight cycle targets. Since station loops are short, actual head demand is modest; confirm the duty point against real plumbing to avoid unnecessary throttling.
FAQ
Q1: Can connection orientation or mounting be customized for skid integration?
A: Customization is supported, with rapid-response technical support during design-in.
Q2: What supply capacity exists for network-wide station rollouts?
A: Monthly production capacity is 10,000 units, with a 20-working-day lead time.
Q3: What warranty and lifetime should station operators expect?
A: Two-year warranty and a working life exceeding 20,000 hours.